rated for 125c, type hzc combines the advantages of aluminum electrolytic and aluminum polymer technology. these hybrid capacitors have the ultra-low esr characteristics of conductive aluminum polymer capacitors packaged in a v-chip, smt case with high capacitance and voltage ratings that were previously available only in aluminum electrolytic technology. applications for type 125c hybrid capacitors include a variety of industrial power conversion, lighting control and automotive applications. highlights - +125 c, up to 4,000 hours load life - low leakage current - very low esr and high ripple current - 260 c ref ow soldering specif cations outline drawing cde cornell dubilier ? 1605 e. rodney french blvd. ? new bedford, ma 02744 ? phone: (508)996-8561 ? fax: (508)996-3830 capacitance range 10 to 330 f capacitance tolerance 20% @ 120 hz/+20 c rated voltage 25, 35, 50, 63 vdc leakage current (at 20c) i = .01cv or 3 a max., whichever is greater after 2 minutes i = leakage current in amps c = rated capacitance in f v = rated dc working voltage in volts low temperature characteristics (at 120 hz) z(-25 oc)/z(+20 oc): 2 z(-55 oc)/z(+20 oc): 2.5 ripple current frequency multiplier frequency 120 hz 1000 hz 10,000 hz 100 khz correction factor 0.1 0.3 0.6 1 rohs compliant type hzc -55 oc to +125 oc smt hybrid polymer-aluminum electrolytic capacitors case code d ( 0.5) l ( 0.3) a ( 0.2) b ( 0.2) h (max.) i (ref.) w p (ref.) k c 5.0 5.8 5.3 5.3 6.5 2.2 0.65 0.1 1.5 0.35 +0.15/-0.20 d 6.3 5.8 6.6 6.6 7.8 2.6 0.65 0.1 1.8 0.35 +0.15/-0.20 x 6.3 7.7 6.6 6.6 7.8 2.6 0.65 0.1 1.8 0.35 +0.15/-0.20 f 8.0 10.2 8.3 8.3 10.0 3.4 0.90 0.2 3.1 0.70 0.2 g 10.0 10.2 10.3 10.3 12.0 3.5 0.90 0.2 4.6 0.70 0.2 mm capacitor markings voltage code voltage vdc e 25 v 35 h 50 j 63 lot, number: year, line, month for f ltering, bypassing and power supply decoupling with long life requirements c film
ratings capacitance (f) voltage rating (vdc) cde part number max dcl (a) max df @ 120 hz/20c max e.s.r. @ 100khz/+20c (ohms) max ripple current @ 100khz/+125c (a rms) d (mm) l (mm) case code qty/reel 25 vdc ( 32 vdc surge ) 33 25 hzc336m025c12t-f 8.2 0.14 0.080 0.55 5.0 5.8 c 1000 56 25 hzc566m025d16t-f 14.0 0.14 0.050 0.90 6.3 5.8 d 1000 100 25 hzc107m025x16t-f 25.0 0.14 0.030 1.40 6.3 7.7 x 900 220 25 hzc227m025f24t-f 55.0 0.14 0.027 1.60 8.0 10.2 f 500 330 25 hzc337m025g24t-f 82.5 0.14 0.020 2.00 10.0 10.2 g 500 35 vdc ( 44 vdc surge ) 22 35 hzc226m035c12t-f 7.7 0.12 0.100 0.55 5.0 5.8 c 1000 47 35 hzc476m035d16t-f 16.4 0.12 0.060 0.90 6.3 5.8 d 1000 68 35 hzc686m035x16t-f 23.8 0.12 0.035 1.40 6.3 7.7 x 900 150 35 hzc157m035f24t-f 52.5 0.12 0.027 1.60 8.0 10.2 f 500 270 35 hzc277m035g24t-f 94.5 0.12 0.020 2.00 10.0 10.2 g 500 50 vdc ( 63 vdc surge ) 10 50 hzc106m050c12t-f 5.0 0.10 0.120 0.50 5.0 5.8 c 1000 22 50 hzc226m050d16t-f 11.0 0.10 0.080 0.75 6.3 5.8 d 1000 33 50 hzc336m050x16t-f 16.5 0.10 0.040 1.10 6.3 7.7 x 900 68 50 hzc686m050f24t-f 34.0 0.10 0.030 1.25 8.0 10.2 f 500 100 50 hzc107m050g24t-f 50.0 0.10 0.028 1.60 10.0 10.2 g 500 63 vdc ( 79 vdc surge ) 10 63 hzc106m063d16t-f 6.3 0.08 0.120 0.70 6.3 5.8 d 1000 22 63 hzc226m063x16t-f 13.8 0.08 0.080 0.90 6.3 7.7 x 900 33 63 HZC336M063F24T-F 20.7 0.08 0.040 1.10 8.0 10.2 f 500 56 63 hzc566m063g24t-f 35.2 0.08 0.030 1.40 10.0 10.2 g 500 hzc 227 m 25 f 24t Cf rohs compliant indicator packaging type capacitance capacitance tolerance voltage code case code code 227 = 220 f m = 20% 25 = 25 vdc see ratings table 24 = tape carrier width (mm) t = tape & reel cde cornell dubilier ? 1605 e. rodney french blvd. ? new bedford, ma 02744 ? phone: (508)996-8561 ? fax: (508)996-3830 part numbering system type hzc -55 oc to +125 oc smt hybrid polymer-aluminum electrolytic capacitors film
cde cornell dubilier ? 1605 e. rodney french blvd. ? new bedford, ma 02744 ? phone: (508)996-8561 ? fax: (508)996-3830 hzc 227 m 25 f 24t Cf rohs compliant indicator packaging type capacitance capacitance tolerance voltage code case code code 227 = 220 f m = 20% 25 = 25 vdc see ratings table 24 = tape carrier width (mm) t = tape & reel type hzc -55 oc to +125 oc smt hybrid polymer-aluminum electrolytic capacitors test apply the maximum rated voltage for 4,000 hrs at +125 c with full rated ripple current. after the test measure the capacitance, df, dcl and esr at +20 c. also measure the esr at -40 c and 100khz. ?c at 120hz capacitance will be within 30% of the initial measured value df at 120 hz df will be 200% of the initial specifed value dcl after 2 minute charge leakage current will be the initial specifed value esr at 100khz/+20 c esr will be 200% of the initial specifed value max. esr at 100khz/-40 c after load life test case code c : 2.0 ; case code d : 1.4 ; case code x : 0.8 ; case code f : 0.4 ; case code g : 0.3 load life test shelf life test test subject the capacitor to 1000 hrs at +125 c without voltage. after the test, return the capacitor to room temperature for two hours and then apply rated voltage for 30 minutes. the after test measurements for capacitance, df, dcl and esr at +20 c will meet the following. ?c at 120 hz capacitance will be within 30% of the initial measured value df at 120 hz df will be 200% of the initial specifed value dcl after 2 minute charge leakage current will be the initial specifed value esr at 100khz/+20 c esr will be 200% of the initial specifed value moisture resistance test test subject the capacitor to 2000 hrs at +85 c/85%rh with rated voltage. after the test, return the capacitor to room temperature and humidity for two hours. the after test measurements for capacitance, df, dcl and esr at +20 c will meet the following. ?c at 120 hz capacitance will be within 30% of the initial measured value df at 120 hz df will be 200% of the initial specifed value dcl after 2 minute charge leakage current will be the initial specifed value esr at 100khz/+20 c esr will be 200% of the initial specifed value temperature cycle test test subject the capacitor to 1000 cycles of temperature change from -55 c to +125 c using the following sequence and durations. step temperature time at temperature 1 -55 oc 30 minutes 2 +20 oc 3 minutes max 3 +125 oc 30 minutes 4 +20 oc 3 minutes max after the test, return the capacitor to +20c for one to two hours before measurement. the after test measurements for capacitance, df, and dcl at +20 c will meet the following; ?c at 120 hz capacitance will be within 20% of the initial measured value df at 120 hz df will be 200% of the initial specifed value dcl after 2 minute charge leakage current will be the initial specifed value appearance no signifcant change in appearance film
cde cornell dubilier ? 1605 e. rodney french blvd. ? new bedford, ma 02744 ? phone: (508)996-8561 ? fax: (508)996-3830 type hzc -55 oc to +125 oc smt hybrid polymer-aluminum electrolytic capacitors reel dimensions case dia. 5 6.3 8 10 w 14 18 26 26 t 3 3 3 3 mm tape dimensions case size (mm) case code w 0.3 a 0.2 b +0.3/-0.2 c 0.5 f 0.1 p 0.1 t1 t2 0.2 d +0.1/-0 p1 0.1 p2 0.1 w1 0.1 6.3 x 5.8 d 16 7 7 9.0 7.5 12 0.4 6.4 1.5 2 4 1.75 6.3 x 7.7 x 8.4 8 x 10.2 f 24 8.7 8.7 12.5 11.5 16 0.4 11 10 x 10.2 g 10.7 10.7 14.5 case size (mm) case code w 0.3 a 0.2 b +0.3/-0.2 c 0.5 f 0.1 p 0.1 t1 t2 0.2 d +0.1/-0 p1 0.1 p2 0.1 w1 0.1 5 x 5.8 c 12 5.7 5.7 8.0 5.5 12 0.4 6.4 1.5 2 4 1.75 mm mm film
type hzc -55 oc to +125 oc smt hybrid polymer-aluminum electrolytic capacitors cde cornell dubilier ? 1605 e. rodney french blvd. ? new bedford, ma 02744 ? phone: (508)996-8561 ? fax: (508)996-3830 recommended land dimensions case code d (mm) a b c c 5 1.5 2.8 1.6 d 6.3 1.8 3.2 1.6 x 6.3 1.8 3.2 1.6 f 8 3.1 4.0 2.0 g 10 4.6 4.1 2.0 recommended refow soldering notes: 1. for 5mm and 6.3 mm case dia., if the peak temperature does not exceed 255 c the time at or above 250 c can increase to 10 seconds. 2. the capacitors in the 8m and 10 mm case dia. can withstand 2 refow processes, if the peak temperature does not exceed 245 c and the time at or abov e 240 c does not exceed 10 seconds. 3. the 2nd refow process should be performed after the capacitors have returned to room temperature. 4. temperature should be measured with a thermal couple placed on the top surface of the capacitor. 5. after refow soldering, the leakage current, d.f., and e.s.r., will meet the initial specifcations, and the capacitance will be within 10% of the initial measured v alue when measured at room conditions. case code case dia. (mm) peak temperature time at or above 250 c time at or above 230 c time at or above 217 c time at or above 200 c number of refow processes c 5 260c 5 seconds 30 seconds 40 seconds 70 seconds 2 d 6.3 x 6.3 f 8 1 g 10 0 50 100 150 200 250 300 120 seconds 160 c peak temperature 200 c 70 sec. 230 c 30 sec . temperature (c) time (sec) mm film
type hzc -55 oc to +125 oc smt hybrid polymer-aluminum electrolytic capacitors cde cornell dubilier ? 1605 e. rodney french blvd. ? new bedford, ma 02744 ? phone: (508)996-8561 ? fax: (508)996-3830 capacitor temperature characteristics 330 f/25v -50 -40 -30 -20 -10 0 10 20 30 40 50 -60 -40 -20 0 20 40 60 80 100 120 140 capacitance change (%) temperature ( c) 0 0.2 0.4 0.6 -60 -40 -20 0 20 40 60 80 100 120 140 d . f. temperature ( c) 0.01 0.1 1 10 100 -60 -40 -20 0 20 40 60 80 100 120 140 initial impedance (ohms) temperature ( c) 100 khz 120 hz 1 khz 10 khz 0.01 0.1 1 10 -60 -40 -20 0 20 40 60 80 100 120 140 initial e.s.r. (ohms) temperature ( c) 100 khz 120 hz 1 khz 10 khz film
type hzc -55 oc to +125 oc smt hybrid polymer-aluminum electrolytic capacitors cde cornell dubilier ? 1605 e. rodney french blvd. ? new bedford, ma 02744 ? phone: (508)996-8561 ? fax: (508)996-3830 capacitor temperature characteristics 330 f/25v at +125 oc with rated voltage life test results -40 -30 -20 -10 0 10 0 1000 2000 3000 4000 capacitance change (%) hours spec. limit: 30% 0 20 40 60 80 100 0 1000 2000 3000 4000 dcl (ua) after 2 min. at rated voltage hours spec. limit: 82.5 ua 0 0.1 0.2 0.3 0.4 0.5 0 1000 2000 3000 4000 d . f. hours spec. limit: 0.28 film
notice and disclaimer: all product drawings, descriptions, specifcations, statements, information and data (collectively, the information) in this datasheet or other publication are subject to change. the customer is responsible for checking, confrming and verifying the extent to which the information contained in this datasheet or other publication is applicable to an order at the time the order is placed. all information given herein is believed to be accurate and reliable, but it is presented without any guarantee, warranty, representation or responsibility of any kind, expressed or implied. statements of suitability for certain applications are based on the knowledge that the cornell dubilier company providing such statements (cornell dubilier) has of operating conditions that such cornell dubilier company regards as typical for such applications, but are not intended to constitute any guarantee, warranty or representation regarding any such matter C and cornell dubilier specifcally and expressly disclaims any guarantee, warranty or representation concerning the suitability for a specifc customer application, use, storage, transportation, or operating environment. the information is intended for use only by customers who have the requisite experience and capability to determine the correct products for their application. any technical advice inferred from this information or otherwise provided by cornell dubilier with reference to the use of any cornell dubilier products is given gratis (unless otherwise specifed by cornell dubilier), and cornell dubilier assumes no obligation or liability for the advice given or results obtained. although cornell dubilier strives to apply the most stringent quality and safety standards regarding the design and manufacturing of its products, in light of the current state of the art, isolated component failures may still occur. accordingly, customer applications which require a high degree of reliability or safety should employ suitable designs or other safeguards (such as installation of protective circuitry or redundancies or other appropriate protective measures) in order to ensure that the failure of an electrical component does not result in a risk of personal injury or property damage. although all product-related warnings, cautions and notes must be observed, the customer should not assume that all safety measures are indicated in such warnings, cautions and notes, or that other safety measures may not be required. film
|
